Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 30 Next »

The following steps should be performed as part of FSM Cloud Connector-specific attachment setup process:

Step 1 - Basic prerequisites

Standard SAP setup

Before proceeding, make sure that attachments of a specific storage type (GOS/BDS/DMS) can be manually added in SAP ECC/S4, as described on the following page: Standard SAP attachment setup

FSM Cloud Connector version

The steps described in this document, including the most important transaction - /PACG/ECM_CUST_ATTA - Inbound / Outbound Attachment Configuration - are available for FSM Cloud Connector add-on 200 (/internal version 1.4.0100 and higher). Due to additional enhancements, it is recommended that the latest available service pack be used. Information about the newest FSM Cloud Connector versions and their release notes can be found on the following page: Releases. Pay close attention to all the attached post-installation steps documents (e.g. UPGRADE TO S4PACG 200 or PACG 200 - post installation steps).

It must be emphasized that the new attachment handling mechanism is significantly distinct from the one available in older FSM Cloud Connector versions. BAdIs implemented for the older attachment handling logic or any local extensions are not supported in this approach. The BAdIs should be reimplemented using new BAdI definitions, dedicated to the new attachment handling mechanism (see: Technical diagrams and https://proaxia-prod-doc.atlassian.net/wiki/spaces/PFCC/pages/1466761219/BAdI+definitions#Attachments).

E.g. a BAdI for additional reference setting - /PACG/ECM_ATTCHM_ADD_REF - is not available in the new inbound attachment class /PACG/ECM_CL_S_IDOC_I_ATTCHM2. The new options in transaction /PACG/ECM_ACTIVE –General Properties of E4C Activity can be used instead (see: https://proaxia-prod-doc.atlassian.net/wiki/spaces/PFCC/pages/1577156636/FSM+Cloud+Connector-specific+attachment+setup#An-optional-step---Attachment-inheriting-customizing).

Running the Setup program

After each FSM Cloud Connector update, run the FSM Cloud Connector setup program (/PACG/ECM_SETUP - FSM Connector's Setup). Make sure to include the options below:

The setup program configures basic parameters, which partially used to be customized by now obsolete transactions. The ‘Cloud Message to DMS object configuration’ table (see: Cloud message to SAP object configuration) is also updated by the setup program.

Inbound/outbound class assignment

Make sure that in transaction /PACG/ECM_CLSASSIGIN -FSM Connector's Incoming Messages Configuration class /PACG/ECM_CL_S_IDOC_I_ATTCHM2 is set as inbound data creat. class for messages /PACG/ECM_ATTCHMIN and /PACG/ECM_SIGNATURE:

Make sure that in transaction /PACG/ECM_CLSASSIG - E4C Outgoing Messages Configuration class /PACG/ECM_CL_S_IDOC_O_ATTCHM2 is set as IDOC class for message /PACG/ECM_ATTCHMOUT:

Step 2 - Enable attachment sending for specific objects

Attachments added to specific objects in SAP ECC/S4 will be transferred to SAP FSM only if they are enabled in dedicated transactions.

Equipment/functional location

Field ‘Send attachment’ in transaction /PACG/ECM_EQ1 - Equipment Settings

Service call

Field ‘Send attachment’ in transaction:

Attachments for service notification-originated service calls (transaction /PACG/ECM_SCTDQ -Service call types (SN) definition) are currently not fully supported.

Item

Field ‘Send attachment’ in transaction /PACG/ECM_ITYPE - Material Group and Company Assignment

Purchase order

Field ‘Send attachment’ in transaction /PACG/ECM_BSART - Properties FSM Purchase order type

Customer (Business Partner of type Customer)

(S4)PACG 200 SP04

Field ‘Send attachment’ in transaction /PACG/ECM_CCUST -General customizing for Customer

Vendor (Business Partner of type Supplier)

(S4)PACG 200 SP04

Field ‘Send attachment’ in transaction /PACG/ECM_CVEND –Vendor – General customizing

Step 3 - FSM Cloud Connector attachment configuration center

Transaction /PACG/ECM_CUST_ATTA - Inbound / Outbound Attachment Configuration serves as FSM Cloud Connector attachment configuration center. Use it to determine how inbound attachments should be stored, which attachments should be blocked from transfer to SAP FSM or customize properties of newly created DMS documents.

Navigate to the transaction’s documentation page: /PACG/ECM_CUST_ATTA - Inbound / Outbound Attachment Configuration. In case of using DMS or BDS solution, pay close attention to the DMS configuration and BDS configuration nodes.

Step 4 - Attachment size configuration

Navigate to the following page to learn more: Attachment size configuration - FSM Cloud Connector - Confluence (atlassian.net)

An optional step - Attachment inheriting customizing

Attachments added to a service order/service notification/equipment/functional location can be inherited by related activities. Attachments added to activities in SAP FSM can be inherited by related service order/service notification/equipment/functional location. These features are enabled using the following fields in transaction /PACG/ECM_ACTIVE - General Properties of FSM Activity:

Learn more about these features on the transaction’s documentation page: /PACG/ECM_ACTIVE - General Properties of FSM Activity

Obsolete customizing

The following customizing fields and transactions are considered obsolete:

  • No labels

If you'd like to help us improve the documentation, please provide your feedback using the communication channels listed here. Learn about support possibilities here.